Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 10, 2011 20:12:17 GMT -5
Finally got my scooter running today. It runs perfect and rides just the same. One issue that popped up is that none of the blinkers work on the bike itself. The mirrors flash and the LED lights attached to the fender flash but the others don't. Where would you guys check first?
The oil light stays on in the dashboard. Tomorrow I am going to check the sending unit with a meter. It has oil (Royal Purple Max Cycle) and appears to have good pressure.
|
|
jmkjr72
contributing staff
Commander 132nd Northern Cav. Division
Posts: 2,779
|
Post by jmkjr72 on Dec 10, 2011 20:40:06 GMT -5
i would start by makgine sure you have a good fully charged battery
then double check all the bulbs and wires
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 10, 2011 21:18:27 GMT -5
Thanks bud, I just put a new AGM battery in with 10amps versus 8amp stock. I should be good there, let's hope it is as easy as a buld but to have all 4 go out is weird. Also they are all LED. This should be fun..lol
|
|
jmkjr72
contributing staff
Commander 132nd Northern Cav. Division
Posts: 2,779
|
Post by jmkjr72 on Dec 10, 2011 21:31:00 GMT -5
if they are all led lights i would look at the flasher too
if its not a flasher for leds there may not be enough load to run it
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 10, 2011 21:52:45 GMT -5
it is factory LED's on the front and back turn signals. I am looking to see how much a new LED flasher relay is and wow, they are not cheap. And hard to get. Love them Koreans..lol
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 10, 2011 22:12:13 GMT -5
I am going to try and test them tomorrow before I order stuff, I learned my lesson with my GY6-150.
|
|
jmkjr72
contributing staff
Commander 132nd Northern Cav. Division
Posts: 2,779
|
Post by jmkjr72 on Dec 11, 2011 10:53:30 GMT -5
also use a mulit meter and make sure you are getting current there you may have an odd fuse that is blown i have only worked on the 50cc hyosungs
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 11, 2011 11:02:09 GMT -5
I think it might be the signal relay. testing it today.
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 25, 2011 23:23:11 GMT -5
Getting the factory LED's from Jeffrey.
|
|
|
Post by Rebel on Dec 26, 2011 10:49:22 GMT -5
did it have leds? or are you replacing bulbs.
|
|
Trancebear
Recruit
Bored Retired Army War Veteran
Posts: 58
|
Post by Trancebear on Dec 26, 2011 21:48:47 GMT -5
The US models of this scooter did not have LED lights but the Euro version did so it is just plug and play. The wiring harness is already there for these lights.
|
|
jmkjr72
contributing staff
Commander 132nd Northern Cav. Division
Posts: 2,779
|
Post by jmkjr72 on Dec 26, 2011 21:55:57 GMT -5
ahh yes the good old we are to close to meet us dot so we wont put the parts in
|
|